Rick's b.log - entry 2013/03/16

Beagle Linux fail

Speaking of Beagle Angstrom, it's crap. I say this because I made a fresh image of the v4.25 distribution from CircuitCo and tweaked the uEnv file so it would display on my video grabber. And this is what I keep getting:

Why is my Firefox so slow?

Yeah.
This must be some sort of record...

Configuring static IP on RISC OS

Symptom:

• Won't connect, networking appears to be dead.
  Most likely your IP address is incorrect, unconfigured, or something else is wrong in your setup.
• I can ping stuff by IP address but I can't go to places by name.
  You'll need to set up the resolver to point to an external DNS server.
• I can enter Google.com and such, but all I keep seeing is "No route to host" or the like.
  You need to set up the gateway address, so RISC OS knows where to direct outbound packets.

Here is a step-by-step explanation of setting up static IP on a RaspberryPi. It's the same for a Beagle, and Pandaboard, and so forth.

The first two things you will need to know:

1. The IP address of your broadband router. This is most likely 192.168.0.1 or 192.168.1.1.
   The two addresses above are links to those addresses. If you are using a working computer connected to your broadband router, click on them in turn (opens in a new tab/window). Chances are one will fail and one will present you with some sort of login prompt for the router. Remember which worked.
2. The IP address you wish to assign to the RISC OS machine. The first three digits of the IP address must match the router (i.e. 192.168.1.something). The final digit can be (almost) anything except 0, 255, and a number already in use. I say "almost" in quotes as some routers enforce limits on the available range of addresses, typically allowing addresses between 10 and 60. Pick a number that is less likely to have already been assigned, such as 15 or 24, if in doubt.

Part zero - don't be a dummy

Part zero-point-five - don't expect the moon on a stick

• How to tell? Easy!
  Click here to open Google (IPv6) in a new tab/window. If it fails (unable to connect), you don't have IPv6; don't worry about it...yet. The address, incidentally, is http://[2001:4860:0:2001::68]/.
  Click here to open Google (IPv4) in a new tab/window. If it fails (unable to connect), you don't have IPv4 and you probably can't use RISC OS with this setup. The address, incidentally, is http://173.194.67.104/.

Part one - getting to the network configuration

There should be an option named "Configure...". Click the left mouse button on this option.

• If you don't have a 'Configure' option (old versions of RISC OS...), you can access the system configuration by opening the root directory of your boot drive and running the !Boot directory. If you are not sure what that means, do this:

     Press: F12
     Enter: Filer_Run $.!Boot
     Press: Enter twice.

You are looking for the "Network" entry. Under older versions of RISC OS, it looked like a yellow/red/blue map of London with a spanner superimposed; while RISC OS 4/Select went for a jigsaw pieces motif. In any case, it should say "Network" below the icon. Click on it. [note: if I don't specify, you click once with the left mouse button]

The Network configuration window will appear:

Under RISC OS 5, there are little green indicators to show which parts of the networking are active. If either AUN or Access are lit up, click on the icon and when the setup window for that component appears, click on the "Enable" tickbox to make it unticked. Then click on the 'Set' button.
This shouldn't be necessary for the default is for these to not be enabled.

• For older versions of RISC OS - you will need to check each in turn. Ensure neither is enabled.
• AUN is "Acorn Universal Networking" which was a way of putting Econet (as in '80s BBC Micro) on to a TCP/IP LAN. Unfortunately it uses a horribly non-standard addressing protocol so any machine with AUN enabled cannot be connected to a live network.
• Access is Acorn's peer-to-peer disc/printer sharing with auto-discovery. You could investigate it later, but that's not what we're discussing today. Note that Access is Acorn specific, it isn't SMB or anything known to non-Acorn machines.

Now click on "Internet" and another window will appear:

If all of these things are grey and cannot be clicked upon, ensure "Enable TCP/IP Protocol Suite" is ticked.

Part two - assigning an IP address

• Don't bother selecting "Serial PPP". That may be there because your computer has a serial port and as such could have a modem connected. If that is all you can see, check your network card is properly fitted.

Once you have ticked the interface, click on the "Configure..." button to the right of the interface name.

Yet another window will open. You can see now why this process isn't complicated, just way more fiddly than it ought to be.

First, tick on the "manually" option in the middle of the window to tell RISC OS that you will be supplying the settings.

Next, enter the desired TCP/IP address for the machine. As I said, I will be using 192.168.1.15; what you use depends upon your system.
You can leave the netmask as "default".

• Older versions of RISC OS do not have a 'default' option for the netmask. Enter 255.255.255.0.

Once you have done this, click on Set.

Then Close the Interfaces window.

Part three - knowing where to send stuff

Back in the "Internet configuration", click on "Routing"...

A window will appear:

Part four - looking up names of stuff

Back in the "Internet configuration" again, this time click on "Host names"...

Yet another window will appear:

Ensure the "Try name server to" option is ticked. Then, under Primary nameserver enter the address of your ADSL router. Most routers contain a name server. How this works is your computer will ask the router, which will ask the provider. Then when it gets a reply it will remember this so the next time your computer asks, it will know and not need to contact the provider. This means less work for the provider's systems and faster times for you. If the provider is smart, they might even have the router preload a small subset of common domain names (Facebook, eBay, Google, etc) every couple of days so the information is already available in the router.

In any case, we need to tell RISC OS how to access this information, which is the point of this step. Click on Set.

Part five - finishing up

In the "Network configuration" window, click on Save:

RISC OS will need to restart the machine. It probably shouldn't need to if you are only altering existing TCP/IP settings; but you might have done something with AUN or Access (which modifies a number of things internally); so the configuration tool takes the safest approach and just restarts the computer.

Obviously, click on Restart now.

This isn't a big hardship. After all, this is RISC OS. On a RaspberryPi it will have restarted and be back in the Desktop in under thirty seconds.

Part six - using it

It's all gone horribly wrong!!!

• Computer won't boot - you'll probably need to post your message on the RISC OS Open forum with some details. There should be some sort of message on the screen to give an indication of what is wrong.
  Rule out the obvious - check the network card is correctly fitted and that the network is plugged into it.
• Computer boots, but not correctly - check you selected the right interface and that AUN and Access are not enabled.
• Network doesn't work - check your IP address is correct. If your router is 192.168.0.x your computer can't be 192.168.1.x. Sometimes you may encounter something with a 10.x.x.x address (rare, but not impossible). In this case, you should match accordingly.
• Network sort of works, another computer is erratic - you probably have the same IP address on both machines. Change one of them.
• Can't access websites! - can you enter the IP address of your router into the browser? Like http://192.168.1.1/ or something? Does that work? If so, your DNS settings are incorrect. As a stop-gap, use 8.8.8.8 (that is Google's Public DNS). If that works, you'll need to investigate your router's DNS capabilities and if it doesn't have any, the address of your provider's DNS server. Unless you're happy with Google potentially knowing all the sites you look at, in which case you can leave it at four-eights.
• I can enter Google and such, but I can't go anywhere - no route to host! - check your gateway is set to point to your ADSL router.
• It still won't work! Wah! - it is unusual but check your router hasn't been set to block new connections or only allow access at certain times of the day. Check the cable itself is good. If you have a netbook or laptop, plug that in using the cable from the RISC OS machine. If it works, there is possibly something wrong with your settings. If it doesn't work, it isn't RISC OS.

Your comments:

Please note that while I check this page every so often, I am not able to control what users write; therefore I disclaim all liability for unpleasant and/or infringing and/or defamatory material. Undesired content will be removed as soon as it is noticed. By leaving a comment, you agree not to post material that is illegal or in bad taste, and you should be aware that the time and your IP address are both recorded, should it be necessary to find out who you are. Oh, and don't bother trying to inline HTML. I'm not that stupid! ☺ ADDING COMMENTS DOES NOT WORK IF READING TRANSLATED VERSIONS.
 
You can now follow comment additions with the comment RSS feed. This is distinct from the b.log RSS feed, so you can subscribe to one or both as you wish.

R benj, 12th April 2021, 09:27

Thankyou

Add a comment (v0.11) [help?] . . . try the comment feed!
		Your name
		Your email	(optional)
		Validation	Are you real? Please type 74605 backwards.
		Your comment